3ddecoupage(11), Craft Creations Magazine

[ Pobierz całość w formacie PDF ]
3D Découpage
By Kathleen Stroud
Materials Required:
P. V.A. Craft Adhesive.
Scissors or knife and cutting mat.
Sticky fixer pads or Silicone adhesive.
3D Découpage paper: DC181 to DC186.
Card mount: AP02U.
How To Make The Cards:
The designs shown in the instructions are all in
the large size using AP02U cards. The prints are also
available in a smaller size to fit AP78U or AP78M
cards (shown right). The découpage sheet codes for
this size are DC193 to DC198. The instructions are
the same for either size.
The first layer of each design is a full print mounted
into the card before following the instructions for your
chosen design.
You can use either silicone adhesive or sticky fixers
to separate the layers. Using silicone glue means you
can vary the spacing between different layers or areas
simply by using a larger or smaller blob of glue. Sticky
fixers are too large as they come and should be cut
into about eight pieces or smaller where necessary.
When the instructions call for glueing,
place the sticky fixer as far as possible from
the area to be glued.
White gaps on the diagrams show a cut.
Red lines show glue.
1. Cut out all parts shown.
Cut between the petals of
the top flower where shown
and gently bend the small
petal down. Sticky fix into
place except for lower 2cm
of stem. Glue bottoms of
stems as shown.
2. Cut out parts shown. Cut
between right flower and
stem where shown. Sticky
fix whole thing into place
glueing right hand flower
and stems where shown.
3. Cut out parts shown. Cut
between the two top petals
and glue into place (no
sticky fixer), along the
edges as shown. Cut be-
tween petals of flower as
shown and gently bend
centre petal down. Sticky
fix into place and glue
flower base where shown.
Sticky fix leaf into place
and glue the bottom.
3
1. White gaps on the diagrams
show a cut. Red lines show
glue. Cut out all parts shown.
Sticky fix top bud into place and
glue stem where shown. Sticky
fix rest into place and glue left
hand flower where shown.
Glue stems at the bottom.
2. Cut out parts shown. On the
right hand side, cut between
leaves and flowers in the four
places shown. Sticky fix the
three flowers and glue where
shown. On the left, cut between
petals of top flower, gently
bend the two side petals down.
Sticky fix into place and glue
where shown. Cut leaf tip from
centre flower. Sticky fix flower,
bud and leaves into place then
glue where shown. Sticky fix
leaf into place, glue at the base.
3. Cut out parts shown. Glue
the leaf at the base and stick
into place with no pad. Once
1. White gaps on the diagrams
show a cut and the red lines
show glue. Cut out all parts
shown. On back flower cut
between the petals and stem
as shown, sticky fix into place
and glue where shown. Cut
between bud and leaf on the
left where shown, sticky fix
bud and glue as shown. Sticky
fix rest of design into place.
2. Cut out parts shown. Put a
little glue onto the backs of
leaves where shown before
sticky fixing into place and
hold centre down until dry. Cut
between the petals on right
hand flower, and gently bend
them to look natural.
1
1
3. Cut out parts shown (except
the very pale bud). Cut be-
tween bottom of stem and leaf,
and top of stem and flower
where shown. Glue top of stem
into place and allow to dry.
The stem crosses over the bud
(shown pale) on the previous
layer, put a tiny dab of glue
onto the bottom of the stem
and, keeping the stem in line
with stem on the previous layer
press the glued end onto the
stem about 2mm further up the
stem than it should be placed.
This will make it gently curve
upward instead of laying flat
on the bud. Sticky fix edge of
leaf into place glueing where
shown. Glue the small green
bud into place at the base only.
When dry gently lift at the top
edge. Cut between flower
petals and sticky fix into place
by centre only. Gently bend
petals to shape.
2
2
3
dry, lift the tip. Cut between
petals on each flower and
gently bend petals to shape.
Sticky fix them into place and
glue where shown. Sticky fix
and glue main leaf into place.
3
4
1. White gaps on the dia-
grams show a cut and the
red lines show glue. Cut
out parts shown and sticky
fix into place then glue the
base of the leaves.
2. Cut out parts shown. Cut
the top flowerhead where
shown, sticky fix and glue
into place. Sticky fix flower
group into place and glue
where shown. Sticky fix sin-
gle flower and leaves into
place and glue as shown.
3. Cut the flowers shown.
Sticky fix into place and
glue the top two where
shown.
1. White gaps on the dia-
grams show a cut and the
red lines show glue. Cut
out all parts shown. Cut the
top seedhead where shown,
bend to shape and sticky
fix into place.
2. Cut out parts shown and
sticky fix into place.
3. Cut out petals shown,
sticky fix into place and
glue the left hand flower
where shown.
1. White gaps on the dia-
grams show a cut and the
red lines show glue. Cut
out all parts shown. Cut
between petals on main
flower and bend them to
add shape. Sticky fix into
place.
2. Cut out parts shown. Cut
between petals on main
flower as shown and bend
to add depth. Sticky fix this
into place and glue attached
leaf where shown. Cut
between bud and leaf
where shown. Sticky fix all
parts into place and glue
stems where shown.
3. Cut out parts shown. Cut
between flower petals as
shown and bend to add
depth. Sticky fix into place
and glue where shown.
5
Hello,
We hope you enjoy this free project. You may hand make copies of this project,
to give away or sell, as many times as you like. You may not use the pattern,
project, text or pictures for any other purpose nor make the project using
any automated process.
The project was taken from a back issue of the Craft Creations Magazine.
All the articles on our web site are at least one year old. If you want the latest
projects, designer profiles, gallery pages and more, then you need to subscribe
to the quarterly Craft Creations Magazine.
Subscription Benefits Include:
*
Afree gift with every issue.
*
Two discount vouchers off Craft Creations products with every issue.
*
A £2.50 off post and packing voucher with every issue.
*
New product information.
*
Prize competitions in every issue.
You can subscribe to the quarterly Craft Creations Magazine or purchase any
of the back issues from our online shop.
http://www.craftcreations.com/Shop/shop.html
The details above are correct as of 1st January 2002, but are subject to change without prior notice.
Craft Creations Limited, Ingersoll House, Delamare Road, Cheshunt, Hertfordshire, EN8 9HD, England.
Tel: 01992 781900 Fax: 01992 634339
[ Pobierz całość w formacie PDF ]