3ddecoupage(10), Craft Creations Magazine

[ Pobierz całość w formacie PDF ]
3D Découpage
By Kathleen Stroud
Materials Required:
P. V.A. Craft Adhesive.
Scissors or knife and cutting mat.
Sticky fixer pads or silicone adhesive.
3D Découpage paper: DC187 to DC192.
Card mount: AP02U or AP02G.
How To Make The Cards:
The designs shown in the instructions are all in
the large size using AP02 cards. The prints are also
available in a smaller size to fit AP78U or AP78M
cards (shown right). The découpage sheet codes for
this size are DC199 to DC204. The instructions are
the same for either size.
The first layer of each design is a full print mounted
into the card before following the instructions for your
chosen design.
You can use either silicone adhesive or sticky fixers
to separate the layers. Using silicone glue means you
can vary the spacing between different layers or areas
simply by using a larger or smaller blob of glue. Sticky
fixers are too large as they come and should be cut
into about eight pieces or smaller where necessary.
When the instructions call for glueing,
place the sticky fixer as far as possible from
the area to be glued.
1. Cut out parts shown.
Sticky fix single leaf into
place. Cut four leaves
where shown. Sticky fix
rest into place and glue
leaves and stems where
shown.
2. Cut out parts shown.
Glue small top leaf at base,
no sticky fixer. Cut between
stem and bud where
shown. Sticky fix top two
buds into place and glue
stems. Sticky fix the flowers
into place. Glue stem where
shown.
3. Cut petals of top flower
as shown and curve centre
part down. Sticky fix into
place. Sticky fix lower
flower into place.
White gaps on the diagrams show a cut.
Red lines show glue.
3
1. White gaps on the diagrams
show a cut. Red lines show
glue. Cut out parts shown. Cut
between stem and top flower
where shown. Sticky fix into
place and glue stem where
shown.
2. Cut out parts shown. Cut
between bud and right hand
flower. Sticky fix two lower
flowers and leaves into place
and glue stems where shown.
1. White gaps on the diagrams
show a cut and the blue lines
show glue. Cut out parts
shown. Cut the upper left leaf
group at stem where shown.
Sticky fix into place and glue
stem. Cut away the top two
leaves on the right as shown
then cut between them where
shown. Sticky fix into place
and glue where shown. Cut
between centre leaf and stems
1
1
2
2
Cut between the petals on top
flower and cut bud from leaves.
Sticky fix bud into place and
glue stem. Sticky fix flower
and leaves into place and glue
flower where shown.
3. Cut out parts shown. Sticky
fix leaves into place and glue
the centre. Cut between the
petals on right hand flower
where shown. Sticky fix into
place and glue two cut stems
as shown.
2. Cut out parts shown. Sticky
fix all upper leaves into place
and glue where shown. Cut
between the two rose hips and
sticky fix back one into place
glueing where shown. Sticky
fix other two hips into place.
3
3
Sticky fix front leaf with rose
hip flower into place and glue
where shown. Sticky fix stem
into place.
3. Cut out the parts as shown.
Sticky fix all parts into place
and glue each one where
shown.
where shown, bend centre petal
up a little. Sticky fix into place
and glue as shown. Cut the left
petal as shown. Bend the edge
down a little, sticky fix into
place and glue where shown.
4
1. White gaps on the dia-
grams show a cut and the
red lines show glue. Cut
out all parts shown and
sticky fix into place.
2. Cut out parts shown.
Sticky fix seed head into
place. Glue both buds into
place where marked with-
out a sticky fixer. Sticky
fix leaves into place. Cut
between the petals on both
flowers where marked.
Bend the petals to accen-
tuate the shapes and sticky
fix into place.
3. Cut out parts shown. Cut
top petal where shown and
sticky fix into place. Bend
the lower flower on the join
between top and bottom
petals and sticky fix into
place. Sticky fix the leaf
into place.
1. White gaps on the dia-
grams show a cut and the
red lines show glue. Cut
out all parts shown and
sticky fix into place.
2. Cut out all parts shown.
Cut between main stem
and leaf stem where shown.
Sticky fix into place and
glue stems where shown.
3. Cut out parts shown.
Sticky fix the berries into
place. Sticky fix part leaf
into place and glue along
top as shown. Sticky fix leaf
into place and glue stem.
1. White gaps on the dia-
grams show a cut and the
red lines show glue. Cut
out all parts as shown. Cut
out the yellow flower centre
and set aside to use later.
Sticky fix the rest into place.
2. Cut out parts shown.
Sticky fix single leaf into
place and glue stem as
shown. Sticky fix rest into
place and glue part leaf
where shown.
3. Cut out parts shown.
Sticky fix leaf into place
and glue at the base. Cut
between the flower petals
and sticky fix flower into
place. Sticky fix the saved
yellow centre into place.
5
Hello,
We hope you enjoy this free project. You may hand make copies of this project,
to give away or sell, as many times as you like. You may not use the pattern,
project, text or pictures for any other purpose nor make the project using
any automated process.
This project was taken from a back issue of the Craft Creations Magazine.
All the articles on our web site are at least one year old. If you want the latest
projects, designer profiles, gallery pages and more, then you need to subscribe
to the quarterly Craft Creations Magazine.
Subscription Benefits Include:
*
Afree gift with every issue.
*
Two discount vouchers off Craft Creations products with every issue.
*
A £2.50 off post and packing voucher with every issue.
*
New product information.
*
Prize competitions in every issue.
You can subscribe to the quarterly Craft Creations Magazine or purchase any
of the back issues from our online shop.
http://www.craftcreations.com/Shop/shop.html
The details above are correct as of 1st January 2003, but are subject to change without prior notice.
Craft Creations Limited, Ingersoll House, Delamare Road, Cheshunt, Hertfordshire, EN8 9HD, England.
Tel: 01992 781900 Fax: 01992 634339
[ Pobierz całość w formacie PDF ]