3S DASH, Mitsubishi 3000 gt

[ Pobierz całość w formacie PDF ]
52A-8
INTERIOR - Instrument Pa
nel
INSTRUMENT PANEL
M52UAAT
For installation of the instrument panel, the bolts and screws described below are used. They are indicated by
symbols in the illustration.
,
4 x
16 (.I6 x .63)
5
x
16 (.20
x
.63)
4 x
12
(.I6 x
.47)
6 x
16 (.24
x
.63)
6 x 25 (.24 x .98)
19N0001
I
I
I
NOTE
D = Thread diameter
L = Effective thread length
TSB Revision
1
 52A-9
INTERIOR
- Instrument Panel
REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operation
Removal and Installation of Floor Console
(Refer to P.52A-11.)
Removal steps
1. Hood lock release handle
2. Rheostat
3. Switch garnish B
4. Knee protector assembly
5. Column cover
6. Glove box striker
7. Glove box and cross pipe cover
8. Center air outlet assembly
9. Heater control assembly installation screws
10. Meter bezel
11. Combination meter
12. Speedometer cable adapter (Mechanical
type speedometer)
13. Speaker or plug
14. Harness connector
15. Steering shaft mounting bolts
16. Instrument panel assembly
i*
19FO131
SERVICE POINTS OF REMOVAL
5. REMOVAL OF COLUMN COVER
Remove the screws and
remove the column cover while
using care not to break the claws.
Front of
TSB Revision
 52A-10
INTERIOR
- Instrument Panel
8. REMOVAL OF CENTER AIR OUTLET ASSEMBLY
Disengaging the clips of the center air outlet assembly with
a flat tip (-1 screwdriver, remove the center air outlet
assembly with the trim stick.
I
I
screwdriver
/
2OFOO321
I
12.
REMOVAL OF SPEEDOMETER CABLE ADAPTER
(MECHANICAL TYPE SPEEDOMETER)
(1) Disconnect the speedometer cable at the transaxle end
of the cable.
(2) Remove the adapter locks from the instrument panel.
(3) Pull the speedometer cable slightly toward the passen-
ger compartment and remove the adapter.
I
I
I
I
I
DISASSEMBLY AND REASSEMBLY
Q
1
d’
I
I
Glove box disassembly steps
1.
Glove box stopper
2. Cross pipe cover
3.
Glove box cover
-
2
w
4. Ratchet assembly
5. Lock cylinder assembly
6. Glove
box
Instrument panel disassembly steps
7. Glove box lower frame
Side air outlet
Photo sensor
Defroster garnish
Heater ducts
I
(Refer to GROUP
55 -Ventilators.)
1
Combination gauge (Refer to GROUP 54 -
Meters and Gauges.)
8. Instrument panel wiring harness
L&i
19FO132
TSB Revision
 52A- 11
INTERIOR - Floor Console
FLOOR CONSOLE
MSZUBAS
REMOVAL AND INSTALLATION
i
Removal steps
1. Cup holder
“‘WQ~~~~ ,_
\
2.
Console plug
/t9
v”@y
3. Rear console assembly
4. Radio panel
5. Radio
6. Switch garnish C
7.
Console side cover
8. Front console garnish
9. Manual transaxle shift lever knob
10. Front console assembly
19FO130
3
b
DISASSEMBLY AND REASSEMBLY
Front console disassembly steps
I. AIT garnish <ATT>
2. M/T shift lever cover <M/T>
3. Ashtray
4. Cigarette lighter
5. Power seat switch
6. Front console
7. Front console bracket
Rear console disassembly steps
8.
Plug
9. Console lid
10. Lock lever
11. Spring
12.
Rear console
19FO129
TSB Revision
 52A-12
INTERIOR
- Trims
I
TRIMS
4
Trim
M52UCW
TRIM CLIP REMOVAL/INSTALLATION PROCE-
DURES
The type of clip shown in the illustration, which is used for the
Eli
~
19POO80
installation of instrument panel, should be removed and
installed by the following procedures described below.
REMOVAL
(1) Use a cross-tip (+) screwdriver to push inward the pin (at
the center of the trim clip) to a depth of about 2 mm (.08
in.).
(2) Pull the trim clip outward to remove it.
Caution
Do not push the pin inward more than necessary
because it may damage the grommet, or the pin may
fall in, if pushed too far.
m
in.)
horn
19POO70
19POO8,
INSTALLATION
(1) With the pin pulled out, insert the trim clip into the hole in
the trim.
(2) Push the pin inward until the pin’s head is flush with the
grommet.
(3) Check whether the trim is secure.
Pin
Trim
19POO82
19POO80
TSB
Revision
  [ Pobierz całość w formacie PDF ]